NAGA

Im going

Yes

If you need a custom frag tank or a custom sump this will be the cheapest time of year. I'm emptying my scrap wall, leftover pieces from all the big tanks. I have a lot of half inch and a lot of three quarter-inch. For those in Virginia if you order this week I can bring them to frag fest meeting. Take a look at my truck in the pic. When we weighed it was 2600 pounds. Your custom sump or frag tank could be in that pile. Example: 2ft sumps $50. Email me jeffhaddock@comcast.net

As the title says $350

I have a aquatic life 6ft. fixture with 3 150 watt lights with T-5 actinics and LED's $450 Link to the light fixture: http://www.marinedepot.com/AquaticLife_HQI_Metal_Halide_Fixtures_with_T5_HO_and_Lunar_LEDs_36_to_38_Inch_HID_Fixture_with_T5-AquaticLife-AK01205-FILTFIMHTSHDT5-vi.html I have the large Aqua Medic Kalkstirrer that is brand new. 8" in diameter and 26" tall THIS IS THE BIG ONE $300 http://www.aquacave.com/Kalkwasser-Stirrer-5000-by-AquaMedic-P1005.aspx I have a Aqua C 180 EV series skimmer $40 in perfect working order I have a Aqua C 120 EV series skimmer $25 in perfect working order

Aqua C 180. $50 Aqua C 240 $100 ETSS 800 $150 Pumps available at additional $$ 72" 3x150watt light fixture with t5 actinics and Led moonlights. This is an Aquatic life brand light fixture.

Aqua C 240. $100 Aqua C 180 $50 ETSS 800. $150

You still need to check with the mfgr. with sch80 as there are differences with holes needed with some brands. Id wait til bulkhead in hand or look at mfgr website.

7 in a 150? Wow and I thought I was brave having 16 in a 750g

I have a number of protein skimmers for sale. 2 qty. of the Aqua C EV-180 $195 with mag pump to run it 1 qty. of the Aqua C EV-240 $250 with Mag pump to run it 1 qty. of the Deltec APF600 $350 No feed pump I also have a glass tank 3x2x2 rimless 1/2" glass (not starphire) with two drains in upper left corner. Tank $300. Tank and steel stand $480 I also have a huge wetdry filter for a 600g or larger tank. $150 wetdry is 4ft. long by 20" by 24" tall with dual chambers/drip trays. if you want pics EMAIL ME for them. You can call also at 410-703-5383

Regardless of the material the material should not break with a clean snap. Whether its cheap material like acrylite FF or Polycast the break should pull material from both surfaces.

The key is that when you go to break it it pulls material from both surfaces. That's a great bond. When it snaps apart and it's smooth or even then it is not a good bond. You'll find Weldon 4 or 3 will break apart pretty clean in a lot of attempts (especially your first go around or two)

Hi Michael., glad you liked the video. This top can be cut out in about 2.5 minutes vs. doing it by hand taking 30 minutes. The accuracy is also to within .003" The router can cut through 2" material in a single pass(16hp). It looks like a snowblower when it's cutting that thick material. Thank you for the business!

I have two Apex Jr. units that are overstock. I have discounted them and only have two available. I can mail them if requested or you can pickup. Payment can be Paypal or cash on pickup. Any questions please feel free to email me at jeffhaddock@comcast.net Thank You!

Hi Mike, thank you for your business. That 1/2" thick stuff looks great!

Piedmont might be a little closer. 1/4" black sheet they have in stock as of last week

Well if someone tells you to go buy a car you certainly do your research on where you go. Just common sense which is what you need for just about everything. I certainly am not advocating you just go find the first cnc router place you run into. Just like most things do your research and if you want a list of places just look for plastic fab shops. I don't know anyone that would cut half inch material with anything smaller than a 1/4" but, I'm sure if you try to find someone you could.) Feed rate, bit type, bit brand, and the tool path chosen all factor in how cuts are done. Just find someone that knows what there doing with plastic.........the accuracy is far better with consitency, squareness, and surface prep.

Hi, I get questions like this all the time. I have been building aquariums, frag tanks, sumps, and reservoirs for over 20 years. With this I can tell you your going to want to play with building a sump or even a topoff tank first before you attempt anything like the size tank your thinking about. 66" by 26" by 20" tall can be made with 1/2". If it's for a reef tank though you'd want the 1/2" to go with a larger opening on top. Now as far as the bonding of the acrylic your going to be limited on what you can get as a lot of the chemicals used are quite hazzardous. I like to make my own solvents but, there is IPS or what is commonly called Weld-on is what is most widely available to the general public. There is Weldon #3, #4, most commonly available solvents. There use to be a #5 but, I believe that is no longer available. The #3 sets up very quickly (fast acting) and does not allow for that great of a bond. So stay away from Weldon #3 for anything over 30 gallons. Weldon #4 is a little better in that is has a little better flow charactoristics and is slower to setup. Your seams that are bonded will yield a little cleaner look to them. Don't let good looking seams fool you though.......just because there is no bubbles in the seam gives you better strength. This is where the testing of scrap material is important. You can actually have bubbles in the joint and yet have a great bond. However, #4 just recently went through a formulation change and IMO more junk went in and more of the good things went out. I don't reccommend it for anything over 150 gallons(so your right there at the limit). So, having said all that if your really going to go for this right out of the gate take your time with lots of scrap material and let it setup for at least 48 hours and see if you can break your test pieces clean. If they snap off clean then you know your not getting a proper bond. If however, when your snapping the test pieces and your pulling out material from both surfaces that is when you know your doing it right. The last thing I'd tell you and it's the most important............have someone cut out the tank pieces with a CNC router table(not a hand router and table). The pieces literally will come to you ready to put together and with perfect accuracy and surface finish to put together. Good luck with this but, be smart about it...........PRACTICE!!!

made with 3/8 and 1/2" material. email me for pictures at jeffhaddock@comcast.net this was an extra that never made it to a tank setup, therefore I am discounting it to move it out. $200

Your going to need 50-60 ml/min to start Steve. Since the system is large any adjustments to that will take time to see the effect. Your probably going to need to test quite a bit to see what adjustments you make move your KH and CAL readings.

Deltec PF1001 cal reactor It will take care of your alk issue

I've got a 150 reef ready aga tank forsale. it has a cherry stand and duel overflow boxes on the back to the tank. Tank was just taken down yesterday and has not been cleaned $250. I also have a 6 ft. 3 x 150 watt metal halide light fixture for sale as well. it also has 4 power compact blues in it. One of the 150 bulbs iis not working so I assume its burned out $150. I also have a ETSS 800 duel stack skimmer $250 no pictures.

Josh After returning your email last night and hearing back from you saying you were going to call me today I never heard from you. From what I can tell it was something that was taped on and not bonded on. I'd like to make sure so call me. Ill work on the pm box

email me at jeffhaddock@comcast.net if your interested. Sump has never been filled and is made with 1/2" and 3/8" thick acrylic. 410-703-5383 Jeff

I have built up a lot of cutoff scrap over the summer and now would like to make something out of what is leaning on my walls. If you need a sump or a frag tank I can do them now for less than for what they regularly would go for. Use my email to send me what you want with as much detail on the specs as you can and if you can google sketch something all the better. I usually get quotes back within 24 hrs. This special is for acrylic. Jeff 410-703-5383