zygote2k October 19, 2017 Share October 19, 2017 On one of my service tanks, the incoming DC water line has been filled with fine particulate that has now clogged 2) RODI units. This results in zero water production and requires a full tear down to fix temporarily until it clogs again. Is there a scale reduction cartridge that I can buy to "prefilter" the water before it goes to the first stage? Can I simply place an empty cartridge first in line in hopes that the particles will fall to the bottom of it before going to the first stage? Need some help on figuring this one out. Thank in advance. Link to comment Share on other sites More sharing options...
Jon Lazar October 19, 2017 Share October 19, 2017 What about adding a coarse sediment filter (or two) as an additional prefilter? One µ is common, and I've seen them as large as five µ. The coarse ones are cheap to replace and won't clog so quickly. Everyone puts their RODI elements in series, but you could add two prefilters and install them in parallel to extend the time between replacement. Or install something larger than the standard 10" cartridge. Link to comment Share on other sites More sharing options...
AlanM October 19, 2017 Share October 19, 2017 On the BRS unit I use the first stage is a 1 micron particle filter and then two 5 micron carbons. Is yours the same? Stuff making it past all that? Link to comment Share on other sites More sharing options...
Jerel October 19, 2017 Share October 19, 2017 Spectrapure has a 0.2 micron ZetaZorb sediment cartridge. I have one on my Spectrapure unit and it is capable of holding five times more dirt than say, 1 micron. Link to comment Share on other sites More sharing options...
John Ford October 19, 2017 Share October 19, 2017 Spectrapure has a 0.2 micron ZetaZorb sediment cartridge. I have one on my Spectrapure unit and it is capable of holding five times more dirt than say, 1 micron. This filter is amazing. Cost 30$ but when I use this in my rodi setup I produce 0 tds before my di chambers. I have a low tds coming into my house to start but I have never seen 0 tds before my di with any other sediment cartridge. (Sorry to stray from the topic) Link to comment Share on other sites More sharing options...
molcott October 20, 2017 Share October 20, 2017 try this https://www.bulkreefsupply.com/dm-fit-filter-strainer.html Link to comment Share on other sites More sharing options...
zygote2k October 20, 2017 Author Share October 20, 2017 try this https://www.bulkreefsupply.com/dm-fit-filter-strainer.html exactly what I was looking for. Thanks. Link to comment Share on other sites More sharing options...
molcott October 20, 2017 Share October 20, 2017 exactly what I was looking for. Thanks. Right on only reason I even knew about that was because BRS put a new video on YouTube yesterday that had that on there Sent from my SM-G955U using Tapatalk Link to comment Share on other sites More sharing options...
AlanM October 20, 2017 Share October 20, 2017 The holes in that filter are really huge at 150 micron. Do you have your RO attached right to the wall with no pre-filters? That's the only way I could see this helping, and even then it will just keep the visible doodoo from getting on the RO. My 1 micron fiber prefilter turns orange over the course of a month with stuff in our water in Gaithersburg. Link to comment Share on other sites More sharing options...
Jerel October 20, 2017 Share October 20, 2017 If you absolutely need an add-on solution. This 0.35 micron pleated filter is more appropriate. Link to comment Share on other sites More sharing options...
Origami October 23, 2017 Share October 23, 2017 The holes in that filter are really huge at 150 micron. Do you have your RO attached right to the wall with no pre-filters? That's the only way I could see this helping, and even then it will just keep the visible doodoo from getting on the RO. My 1 micron fiber prefilter turns orange over the course of a month with stuff in our water in Gaithersburg. My guess, from Rob's original post, is that his first stage sediment filter is clogging - not that his membrane is fouling. A 150 micron stage is probably a good start at knocking out the big particles of scale. A 100 or even a 50 micron stage would be good as well and take some of the load off of the first stage. As that first stage gets clogged, the efficiency and output of the RO falls off drastically. The pre-filter stage that was suggested looks ideal. Even more so because the 100 mesh screen is removable and cleanable as part of routine maintenance. A quick search on the internet shows that you can buy these straiers in 200 mesh (60 micron) versions, too. Link to comment Share on other sites More sharing options...
zygote2k October 23, 2017 Author Share October 23, 2017 I have a standard 5 stage rodi. The incoming line from the source has had black particles of something in it that clogs the actual tubing as it enters the prefilter. Link to comment Share on other sites More sharing options...
AlanM October 23, 2017 Share October 23, 2017 Yikes. City must pump directly from the reservoir. Link to comment Share on other sites More sharing options...
Jon Lazar October 23, 2017 Share October 23, 2017 I have a standard 5 stage rodi. The incoming line from the source has had black particles of something in it that clogs the actual tubing as it enters the prefilter. How about this? It's a spin-down sediment filter. Plumbingsupply.com carries them. Link to comment Share on other sites More sharing options...
Origami October 23, 2017 Share October 23, 2017 I have a standard 5 stage rodi. The incoming line from the source has had black particles of something in it that clogs the actual tubing as it enters the prefilter.Plugs the tubing? That's incredible. Sent from my SM-G930V using Tapatalk Link to comment Share on other sites More sharing options...
John Ford October 23, 2017 Share October 23, 2017 I have a standard 5 stage rodi. The incoming line from the source has had black particles of something in it that clogs the actual tubing as it enters the prefilter. It's been my experience with plumbing that black particles come from the water heater. Obviously your rodi is tied into the cold water so maybe look for possible backflow from the water heater. Also older fixtures start to rot and the gaskets break apart. Is this unit tied into the main water line or tapped off a sink? Link to comment Share on other sites More sharing options...
John Ford October 23, 2017 Share October 23, 2017 Of course D.C. Water has its own line of issues as well so I understand my above comments maybe irrelevant.. Link to comment Share on other sites More sharing options...
zygote2k October 24, 2017 Author Share October 24, 2017 it's tapped off of a sink and it's from one of the main water lines in a lobby hi-rise. It's the tank that Phil used to work on 7 years ago... Link to comment Share on other sites More sharing options...
AlanM October 24, 2017 Share October 24, 2017 Sheesh, I'm surprised all of their faucet aerators don't quickly clog. Surprised they can take showers or wash hands and dishes with that much crud coming through the pipes. Wonder if they have a booster pump in the building to push pressure to the higher floors that has some failing seals or something. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now