dpassar12 April 6, 2019 Share April 6, 2019 (edited) Any tips for keeping stainless fragging tools free of rust? I wash with freshwater after use and still get rust on some of my stainless tools. Edited April 6, 2019 by dpassar12 Link to comment Share on other sites More sharing options...
linkfalcon April 7, 2019 Share April 7, 2019 Some stainless is just coated steel not pure stainless best is to wash them like your doing Link to comment Share on other sites More sharing options...
DFR April 7, 2019 Share April 7, 2019 I’d just continue your freshwater rinses then dry the tools. Saltwater is mildly corrosive so just using your tools in it will eventually promote rust. Link to comment Share on other sites More sharing options...
paul b April 7, 2019 Share April 7, 2019 Buy better stainless steel tools. Good stainless doesn't "hardly" rust. Cheaper stuff or anything from China does. Stainless is made from a few different metals and iron is the cheapest so the stuff with the most iron in it rusts. Link to comment Share on other sites More sharing options...
DFR April 7, 2019 Share April 7, 2019 @paul bAny specific brands that you had good luck with? Link to comment Share on other sites More sharing options...
WheresTheReef April 7, 2019 Share April 7, 2019 I wouldn't worry too much about rust on your fragging tools. Just use and rinse them as you are doing. Link to comment Share on other sites More sharing options...
paul b April 8, 2019 Share April 8, 2019 On 4/7/2019 at 7:35 AM, DFR said: @paul bAny specific brands that you had good luck with? Just about anything made in the US should be fine. Link to comment Share on other sites More sharing options...
ReefdUp April 9, 2019 Share April 9, 2019 Stainless steel doesn't mean it won't corrode. It just "stains less". It has been a while since I've dealt with material selection in a saline environment, but I think 316L is a fairly decent choice if memory isn't failing me. It would need to be passivated. So, good luck finding that, or any frag tools that'll actually tell you the metal and post-processing. Made in America or made anywhere else may or may not be better than the other. A lot of our metals come from other countries, and most places won't pay for certified metals (to US standards). American machining may be better, but the material may still be the same. You can find a few frag tools that are powder coated, but the powder tends to chip off. The corrosion then occurs under the powder where you can't address the corrosion anymore. I'm not a fan.I'd just avoid prolonged exposure to bleach and saltwater. Rinse well. I usually clean mine with vinegar, but I think citric acid may work as well. I keep mine in a pouch with a desiccant. I'm sure there's some sort of water displacement lubricant that is reef safe and compatible with stainless, but I'm out of top-of-my-head thoughts.Sent from my SM-G935P using Tapatalk Link to comment Share on other sites More sharing options...
BtmDweller April 9, 2019 Share April 9, 2019 I’ve been happy with a pair of BRS cutters purchased. Only had them for six months but rise and dried several times and no rust yet. Link to comment Share on other sites More sharing options...
gmerek2 April 11, 2019 Share April 11, 2019 The large one is ecotech. The small is BRS. They are 4 years old or so. Occasionally I have to run hot water over them and work them hard and fast to loosen them up from all the rust. We put the stuff in a bad corrosive environment Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now