jayh

September 25, 2018

Here is my received list: 07 was the $99/m plan, after that, the $199/m

07/18
WWC Hailsorm Acro
WWC Bob Marley Zoa
WWC Blizzard Acro
WWW Limelight Hydno

08/18
WWC Superman Rhodactis
Rainbow Aussie Lord
WWC AOI Zoa
WWC Purple Up Acro
ORA Hawkins Blue Acro

09/18
ORA Pearlberry Acro
Tyree Pink Lemonade Acro
WWC Dayglo Acro
JFOX BiPolar Favites
WWW Gold Interstellar

September 25, 2018

I'll post up tomorrow what I have received so far.

I requested basically all, as I have a fairly empty tank at the moment and really would like to watch them grow out. As they grown and if I decide to frag them out to help recover the costs that would be a good thing, but more than likely I'll just end up giving frags away or trade them for others.

September 24, 2018

I'm doing the gold. Seems to be pretty good value. The samples they provide are not terrible. They are generally the smallest retail size, not just a single shot of whatever.

They don't send you duplicates and you can select the species of coral you want.

Think of it more of a box of the month club. Yes local people have some great corals as well and I'm sure my $200 could go further, but to each their own.

September 17, 2018

You have to update the firmware and the code on the box itself, then the cloud works a bit better. I just wish they would intergrated it into the box itself. Do you have update enabled in the settings? Without that enabled, it does not send test data to the "cloud"

September 16, 2018

I picked one up and set it up. That's louder than expected and the time to test is ~12 mins total. With that being said, it's pretty awesome. Out of the box it was about .1 higher than the Hanna checker. Going to do a few more comparisons over the next few days to really dial in the offset.

One thing it's missing is it own internal webpage. I really wish the would implement that capability, but not sure if the system can support that.

July 22, 2018

my recommendation would be to reduce it after the union, so you would need to use 1 1/2 unions. That way, if you want to move the overflow to a larger tank, you can and support a larger overflow. Just my .02...

July 21, 2018

All the murky beginnings of a cycle. I went the Dr. Tims route. And before people point out, yes the overflow tubes below are reverse. I broke the stupid thinest plastic in the world nut on the main return, so I move the emergency return over just to get the water flowing. Redsea is sending a replacement, but I also purchased one which will be here on Tuesday at the latest, so I have to deal with the noise until them. Going to pickup some R4221 connections from RedSea so I can do my own overflows, in the event of another failure.

The PVC pipe shows up today, so I get to start on that manifold for the pump return and get rid of the flexitube.

Also picked up some super sexy cups rather than filter socks. These came from Australia, as I was not a fan of the Red Sea cups they sell. Yes they were more, but I picked up some regular 4inch ones to replace socks on other sumps as well.

July 19, 2018

I added two more small islands off to each side. One will be for a Zoa garden so it does not take over the main structure and the other I'm not sure. Starting to fill the tank SLOWLY with rodi water now. Going to use the sump as the salt mixing station The two shelves are setup to be for SPS, lower areas are going to be for the less light desired corals.

Also the lights are going to drop 4 inches. Cannot wait to finish getting the water/salt in so I can get some par readings on the various future coral homes..

July 19, 2018

So here is my initial scape. I used Marco rock. Also, I'm going to add two small islands one on each side. Make a zoa island and something else, not sure yet. Thoughts?

July 17, 2018

Didn't reply to the cost factor, with kessil you would need to purchase the controller as well, or buy/build the Kessil to Apex cable.. I would though ecotech into the mix, as the Reeflink controller can also be used to manage the wave pumps if you have them. Ecotech also has a special module you would have to purchase if you wanted to control them with the Apex.

July 17, 2018

So I have a few. 3 AI Prime HD's and 3 Hydra 52 (non HD).

Here is the deal with the Apex integration. The new Hydra 26/52HD (do not believe the primes) will in a future Apex update will be able to be controlled by the Apex, or so we have been told. This will only be on the Apex 2016 model. There is no ETA on when that will be available. On the old ones (non-HD) you need either a discontinue Apex module to control them, good luck finding that!

I just use the Aquailluminaition website to manage the lights, very rarely play with them after they were setup. Sometimes just tweak the balance a little bit, but I'm not in it every day. They are plugged into the EB8 power strip, so if the tank over heads the Apex shuts that power port off to assist in reducing the heat. That is the only Apex integration I have done.

I have one of the AI Primes over a 10g nuvo that I use as my Frag/QT tank and one over my Fish/QT tank at the moment. I had two over my 72g Bow front before it was taken down due to a stand issue. I'm currently planning on putting 2 of the Hydra52(non-HD) over a Red Sea 525, still working on that build. The test run that I did they appear to be good, however I will not know Par levels until I get water in that tank, then I will map the par values out with the Seneye meter. There is a Club Par meter that is available as well.

BRS has done some great videos about the various lights and the PAR levels they put out.

This link is someone who uses the Hydra 26 on a red sea.

I would buy them again. Once I get mine up and running, I'll provide the PAR map with lights that I have.

Edit: Spelling is hard and formatting

July 13, 2018

Yeah, glass thickness is about 1/8 of an inch. It's not tempered as others have drilled on them with success. I was eyeballing a drill press to help out with keeping it straight. Good call on the distance from the edge.

Thanks for the inputs!

edit: spelling is hard...

July 13, 2018

So, for the tank moved in yesterday and mounted in place. Debating between a flexible tube from the return pump and return or do a pic shot. I kinda like the lower loss with the flexible tube. That's TBD. Right now the tank is filled with tap water to leak test it, get flows dialed in and do a general cleaning of the tank. I ha e 4 gallons of distilled vinigar that I was thinking of dumping in just to make sure any mfg residue is removed before switching over to rodi water, thoughts?