Jump to content

TonyInVa

WAMAS Member
  • Posts

    1,004
  • Joined

  • Last visited

Everything posted by TonyInVa

  1. I spot feed Reef Roids once a week. Sent from my SM-N975U using Tapatalk
  2. I do use a Kalk Stirrer. Currently my ph isn't bad. According to my Apex the low has been around 8.1 at night and high is 8.3. But last Winter I remember it being around 7.8. I will see what my options are as far as running my skimmer intake outside.
  3. Anyone using a CO2 scrubber. I was thinking of buying one to use during the winter as my ph goes down. Sent from my SM-N975U using Tapatalk
  4. Hello Paul. Sorry for not clarifying, but it is an led light fixture. If I am understanding you correctly, I would just bridge the positive and negative on the solder points where the bulb touches the board. I would do this with a piece of insulated wire. Here is a picture of the type of led used.
  5. Hello. I have an old Reef Breader light fixture. Half the lights are not lit. In the past when this would happen, I would just find the bulb that appeared burnt and replace. I have done that but still half are not lit. I ensure the negative was to negative and positive give to positive. I believe it is a good solder. I dont think it is the ballast but not sure. How would I go about testing things with a multimeter?
  6. I got it to stop leaking. if it continues down the road, I will try this method.
  7. I have a kalk stirrer that is leaking where the acrylic tube meets the acrylic base plate. I tried just applying more silicone, but that didn't work. I would like to separate the base plate from acrylic tubeso that I can reseal it. I used a heat gun to remove what silicone I could but could not separate the two. The heat softens the silicon. I am afraid to heat it any more, as I don't want to warp the acrylic. Any suggestions would be appreciated.
  8. Hello group. I have a huge Rainbow Anemone. I think I am going to have to rehome. Before I do, I will ask a question that I think I know the answer to. This anemone's tentacles have become very long and stringy instead of bubble tipped. Is there a way to get them to not be stringy and be bubble tipped like it was when it was smaller. I have seen this asked in many forum and always never heard of a proven method to keep the bubbled instead of stringy
  9. That's what I have as well over my tank. Sent from my SM-N975U using Tapatalk
  10. I just installed them three days ago. Sent from my SM-N975U using Tapatalk
  11. I was hoping to use the slots already drilled out. But I may not have a choice. I did find some hinges that would work but would have to use a router to get them to be flush mounted. Sent from my SM-N975U using Tapatalk
  12. Anyone known what these type of cabinet hinges are called? The left side is plastic and the right side is metal. These are rusted and about to break. The ones on the right door have already broke. I can't find them anywhere. I am hoping if I have the name I can find them on line. Sent from my SM-N975U using Tapatalk
  13. I never knew they offered a WAMAS discount. I have been buying filters from them for years.
  14. I have had a wrase that pretty much lost all its tail and top fin, due to an aggressive six line. The injured wrasse has almost made a full recovery.
  15. No I do t have a dimmer. Rapid does sell them and I will go that route. Thanks for your help. Sent from my SM-G965U using Tapatalk
  16. Would adding additional LEDs have an effect?
  17. I did say in parallel, but I meant in series as in the video. I'm sorry but I am a dummy when I comes to electronics. I am using these two LEDs https://www.rapidled.com/solderless-cree-xm-l2-cool-white-led/ https://www.rapidled.com/solderless-ultramarine-royal-blue-led-440-445nm/ These LEDs are limited to 1000mA. So does that mean if the driver has a max output of 1400mA it could blow the LEDs? Is there a way to fix this?
  18. Hoping someone can help me troubleshoot a DIY LED issue. I am using This driver. https://www.rapidled.com/mean-well-hlg-240h-c1400b/ Which states that it can handle 29-59 LEDs ang 179 volts. I am running 27 blues at 3.4 vlts=91.8vlts And also running 16 whites at 2.8 vlts=44.8 Totaling=136.6 volts The problem I keep having, is that an led blows after several hours of use. The leds are wired in parallel as demonstrated in this video below. I have set up many of the projects with the smaller drivers and never had any problems. This is my first time using the driver designed for high quantities of LEDs.
  19. At about 11:20 in this video Jason Fox talks about using all actinics. I found this very interesting. Sent from my SM-G965U using Tapatalk
  20. You can also google aquascape. That will give you Ideas. Depending on what kind of coral you are planning on keeping may steer your aqua scaping.
  21. Some are very easy to change, if you know what type and can get them. I did try google to find out, but had no luck.
  22. Something you also could consider, is to possibly change out some of the LEDs. Since you are not turning the whites up to 100% and using the full potential of that channel. You stated you did not like the look of the whites at 100%, you could change some of the white LEDs to different spectrums of blue or other colors.
  23. I have had success putty some kalk paste on them and killing them. Just do a few at a time. Sent from my SM-G965U using Tapatalk
×
×
  • Create New...