AlanM July 31, 2014 Share July 31, 2014 What does the dial do in Else mode? The internet says that it just speeds up how often the power changes while in Else mode. Which direction is the most variability? Is it all the way counterclockwise or all the way clockwise? Do the S1, S2, S3 do anything in Else? The internet says no. Link to comment Share on other sites More sharing options...
Der ABT July 31, 2014 Share July 31, 2014 i htink the the right it switches speed more often and too the left it holds more but i could be wrong Link to comment Share on other sites More sharing options...
AlanM July 31, 2014 Author Share July 31, 2014 Is right clockwise? Link to comment Share on other sites More sharing options...
Der ABT July 31, 2014 Share July 31, 2014 correct Link to comment Share on other sites More sharing options...
epleeds July 31, 2014 Share July 31, 2014 I thought the dial was only used for the wave function. Else mode is random. Link to comment Share on other sites More sharing options...
YHSublime July 31, 2014 Share July 31, 2014 This is a rough translation of the instructions by somebody who speaks Chinese: User instructions and functional analysis of panelUp to 7 models to choose from: choose different mode by using “MODE/FEED” bottom. The mode functions are as following:H1: Fixed maximum flow mode.H2:75% fixed maximum flow mode.H3:50% fixed maximum flow mode.W1: Classical wave mode:This bottom can work with the big knob on left side to adjust the size of wave in the tank. Every water tank is different. When length of water tank is equal to a length of wave, the wave can reach to maximum peak. When you adjust knob clockwise, it increases a length of wave, otherwise it will decrease a length of wave.Tips: slightly adjust knob and wait 10 seconds more to watch wave, in thus to get the best wave you want.With bottom “SPEED/LOCK” and choose one of S1, S2,or S3 for W1 mode. There are 3 types to control stream.S1: maximum stream.S2: 75% maximum stream.S3: 50% maximum stream.W2, W3: Fixed program pattern for waves and streams:Based on different creatures in the tank, work with knob to change types of waves and streams.Else: Non-fixed program pattern for waves and streams:Based on different creatures in the tank, work with knob to change types of waves and streams.Feeding function:Hold “MODE/FEE” bottom for 3 seconds until “10min” (blue light) on. At this time, water pump stopped and water calms down, then it’s a time to feed. The pump will back up after 10 minutes. Press “MODE/LOCK” bottom until “10min” (blue light) off to manually re-start pump.Lock functionHold “SPEED/LOCK” bottom for 3 seconds until “LOCK” (red light) on. At this time you will lock all functions you set. Hold “SPEED/LOCK” until red light off to unlock if you want to change waves and streams.1.Light function:The light sensor element is located at left side of control box with 2-pin seat. If you do not need this element you can un-plug it.Day time with strong light, the “sensor” yellow light off, and green light on. All functions are under normal control. At night time or clouded day time the “sensor” yellow light on. The waves and streams switch to slow motion.Precautions1.Do not run it when tank has no water.2.Avoid getting water on the surface of control box.3.To install magnetic disk, it is better to move the front disk slowly on outside of the tank glass and make it tight.4.Non-professionals should not open control box User instructions and functional analysis of panelUp to 7 models to choose from: choose different mode by using “MODE/FEED” bottom. The mode functions are as following:H1: Fixed maximum flow mode.H2:75% fixed maximum flow mode.H3:50% fixed maximum flow mode.W1: Classical wave mode:This bottom can work with the big knob on left side to adjust the size of wave in the tank. Every water tank is different. When length of water tank is equal to a length of wave, the wave can reach to maximum peak. When you adjust knob clockwise, it increases a length of wave, otherwise it will decrease a length of wave.Tips: slightly adjust knob and wait 10 seconds more to watch wave, in thus to get the best wave you want.With bottom “SPEED/LOCK” and choose one of S1, S2,or S3 for W1 mode. There are 3 types to control stream.S1: maximum stream.S2: 75% maximum stream.S3: 50% maximum stream.W2, W3: Fixed program pattern for waves and streams:Based on different creatures in the tank, work with knob to change types of waves and streams.Else: Non-fixed program pattern for waves and streams:Based on different creatures in the tank, work with knob to change types of waves and streams.Feeding function:Hold “MODE/FEE” bottom for 3 seconds until “10min” (blue light) on. At this time, water pump stopped and water calms down, then it’s a time to feed. The pump will back up after 10 minutes. Press “MODE/LOCK” bottom until “10min” (blue light) off to manually re-start pump.Lock functionHold “SPEED/LOCK” bottom for 3 seconds until “LOCK” (red light) on. At this time you will lock all functions you set. Hold “SPEED/LOCK” until red light off to unlock if you want to change waves and streams.1.Light function:The light sensor element is located at left side of control box with 2-pin seat. If you do not need this element you can un-plug it.Day time with strong light, the “sensor” yellow light off, and green light on. All functions are under normal control. At night time or clouded day time the “sensor” yellow light on. The waves and streams switch to slow motion.Precautions1.Do not run it when tank has no water.2.Avoid getting water on the surface of control box.3.To install magnetic disk, it is better to move the front disk slowly on outside of the tank glass and make it tight.4.Non-professionals should not open control box User instructions and functional analysis of panelUp to 7 models to choose from: choose different mode by using “MODE/FEED” bottom. The mode functions are as following:H1: Fixed maximum flow mode.H2:75% fixed maximum flow mode.H3:50% fixed maximum flow mode.W1: Classical wave mode:This bottom can work with the big knob on left side to adjust the size of wave in the tank. Every water tank is different. When length of water tank is equal to a length of wave, the wave can reach to maximum peak. When you adjust knob clockwise, it increases a length of wave, otherwise it will decrease a length of wave.Tips: slightly adjust knob and wait 10 seconds more to watch wave, in thus to get the best wave you want.With bottom “SPEED/LOCK” and choose one of S1, S2,or S3 for W1 mode. There are 3 types to control stream.S1: maximum stream.S2: 75% maximum stream.S3: 50% maximum stream.W2, W3: Fixed program pattern for waves and streams:Based on different creatures in the tank, work with knob to change types of waves and streams.Else: Non-fixed program pattern for waves and streams:Based on different creatures in the tank, work with knob to change types of waves and streams.Feeding function:Hold “MODE/FEE” bottom for 3 seconds until “10min” (blue light) on. At this time, water pump stopped and water calms down, then it’s a time to feed. The pump will back up after 10 minutes. Press “MODE/LOCK” bottom until “10min” (blue light) off to manually re-start pump.Lock functionHold “SPEED/LOCK” bottom for 3 seconds until “LOCK” (red light) on. At this time you will lock all functions you set. Hold “SPEED/LOCK” until red light off to unlock if you want to change waves and streams.1.Light function:The light sensor element is located at left side of control box with 2-pin seat. If you do not need this element you can un-plug it.Day time with strong light, the “sensor” yellow light off, and green light on. All functions are under normal control. At night time or clouded day time the “sensor” yellow light on. The waves and streams switch to slow motion.Precautions1.Do not run it when tank has no water.2.Avoid getting water on the surface of control box.3.To install magnetic disk, it is better to move the front disk slowly on outside of the tank glass and make it tight.4.Non-professionals should not open control box Link to comment Share on other sites More sharing options...
kjamaya August 10, 2014 Share August 10, 2014 How do you get waves on w2,3 mode? Everytime I turn to that setting it just pushes water nothing else... Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now